SLUDGE JUDGE® - 15 FT. (4.60 M)

4 options available

Product #: C09247

SLUDGE JUDGE® ULTRA - SUPER STRONG

4 options available

Product #: B01386

SLUDGE JUDGE® II EXTENSION SECTION - 5 FT. (1.53 M)

3 options available

Product #: B01357

CASE FOR SAMPLER

Product #: C09249

CLEANING BRUSH - 6 FT. (1.83 M) L. 1 IN. (2.54 CM) DIAMETER BRISTLE

Product #: B01291

CLEANING BRUSH

Product #: B01361

美国Sludge Judge液心取样器，区授权代理, 上海诚柯检测设备有限公司

The Sludge Judge® is designed to take accurate readings of settleable solids, 5% or less, in a variety of liquids, to any depth. It is ideal for sewage treatment plants, chemical plants, and food processing facilities - anywhere that accurate sample levels of settleable solids in noncaustic materials are needed. The unit holds approximately 3 oz. per foot (89 ml per 0.31 m). The Sludge Judge® comes in 5 ft. (1.53 m) sections of 3/4 in. (1.90 cm) plastic pipe with screw-type connectors. The top section includes a nylon rope for raising and lowering the sampler. Individual sections can be combined as required to achieve the length needed. Do not use in liquids over 165° F (74° C). Sludge Judge® is not autoclavable. A convenient cotton canvas carrying case that holds four sections, a cleaning brush, cleaning rod, and cotton strips are available.

To use:

1. Slowly lower the Sludge Judge® to the bottom of the tank. The float valve opens (see figure A), allowing materials to flow in. When the bottom has been reached and the pipe has filled to the surface level, tug slightly on the rope as the unit is raised. This sets the check valve(see figure B), trapping the mixture inside.

2. When the unit has been raised clear of the liquid, the amount of solids in the sample can be read using the 1 ft. (0.31 m) increments marked on the pipe sections. To release the material in the unit, touch the pin extending from the bottom section against a hard surface. This opens the check valve to drain the sample. One-year warranty.

Do NOT use for sampling ethanol or ethanol blended fuel. Use Nasco fuel sampler (B01477).

Sludge Judge®可读取各种液体中5%或以下的可沉降固体至任何深度的读数。它是理想的污水处理厂，地沟油，废弃油脂，化工厂，食品加工设施-任何地方都需要准确的样品水平的沉淀固体在非奥斯汀材料。该装置的容量约为每英尺3盎司（每0.31米89毫升）。Sludge Judge®有5英尺（1.53米）的3/4英寸截面。（1.90 cm）带螺纹接头的塑料管。顶部包括用于提升和降低采样器的尼龙绳。可以根据需要组合各个部分，以达到所需的长度。不要在温度过165°F（74°C）的液体中使用。Sludge Judge®不可高压灭菌。一个方便的棉帆布手提箱，可容纳四个部分，一个清洁刷，清洁棒，和棉条。

使用方法：

1. 慢慢地将污泥降到水箱底部。浮阀打开（见图A），允许物料流入。当到达底部且管道已填充至表面水平时，当装置升起时，轻轻拉动绳索。这就设置了止回阀（见图B），将混合物困在里面。

2.     2当装置从液体中取出后，可使用管段上标记的1 ft.（0.31 m）增量读取样品中的固体量。要释放装置中的材料，请将从底部延伸的销碰到坚硬的表面。这将打开止回阀以排放样品。一年保修。

不得用于乙醇或乙醇混合燃料的取样。使用Nasco燃料取样器（B01477）。

相关介绍:

1.产品简介

SLUDGE JUDGE污泥采样器可采取任何深度的液体中5%或更少的污泥。非常适用于污水处理厂、化工厂、食品加工厂及任何需要在非腐蚀水体中采取沉积物的场合。

污泥采样器的标准配置为三段长各1.5米、直径为1.9厘米，带有螺旋式连接器的透明塑料管。每米大约可容纳290毫升样品。污泥采样器的顶端部件配有用于提升或降低采样器的尼龙绳。每个部件能够组合起来，获得需要的采样管长度。配件有帆布袋，清洁刷，棉制清洁布以及铝制加固杆（采样管长度过4.6米时必须使用）。配有标准版和加强版可供选择，加强版采样管选用聚碳酸酯材料，具有抗冲击、抗热畸变性能，而且耐候性好，硬度高的特性。

2.主要特点

获取沉积固体的准确读数

采样管的长度可定制（*小4.6米）